How to Fix a Dripping Showerhead

If your shower keeps dripping long after you’ve shut off the water, you’ve probably got a bad valve. It’s an easy repair you can do yourself in under an hour.

The valve behind your shower's handle is the most frequent cause of dripping from the showerhead. And while it might seem like a daunting thing to replace, it's actually pretty easy. The first step is to turn off the main water valve to the shower and then follow these easy steps.

Photo by: Derek Trimble

Derek Trimble

Remove Trim Pieces

After you’ve turned off the water to your shower, you’ll need to remove the faucet handle. Depending on the manufacturer you’ll either pry this off with a small flat head screwdriver or you may have a small allen bolt holding the knob from underneath that you’ll need to unscrew. If it’s the latter, look for a tiny hole on the underside of the faucet handle. This shower has two controls (pressure and temperature) so there are a few more parts but the principle is the same. Next, unscrew the outer plate with a Phillip’s head screwdriver and set everything aside.

Remove Valve Collar

The next step is the easiest one, but it comes with a word of caution. You want to remove the shiny collar that rests over the valve just by pulling it by hand. However, the rubber gasket that’s underneath the collar needs to stay behind. It’s a good idea to roll this backward so it’s out of your way, but you’re going to need it when you put things back together.

Gently Remove Valve Bushing

Remove Valve Bushing

Photo by: Derek Trimble

Derek Trimble

Now you should notice that there’s a large brass bushing that holds the valve in place. The best way to unscrew this is with a soft rubber strap wrench. This will keep you from marring the surface and it’s a safer and easier way to grip something wet and slippery. Tighten the strap around the bushing and crank it gently to the left. Be prepared for some water to come out, there’s likely still a little pressure behind the valve. Do not unscrew the entire bushing all at once. Go slowly, let the water seep out and only take the bushing off. There are a few springs resting behind the valve and if you go too fast, everything is going to come flying out.

Removing Valve and Seals

Slowly remove the valve and use your flashlight to peek inside the valve body. You’ll see two holes for water; hot on the left and cold on the right. Make note of which side the hot water is on (stick a piece of masking tape on the shower wall if you’re forgetful) this will be important during your re-build. Each hole has a small gasket around it, and a set of grommets with springs set inside. The best tool for removing and installing these parts is a pencil. Stick your pencil in each hole and remove the grommets, then gently remove the outer gasket.

Replace or Rebuild? It’s Up to You

Photo by: Derek Trimble

Derek Trimble

At this point, you have a choice. If your valve looks to be in good condition, you can simply install new gaskets and grommets and put everything back together. It’s a good way to save money, but since you’ve done the work this far it’s probably best to replace the whole valve. This is also a good opportunity to change out your shower trim if you’re looking to update your shower faucet. No matter which option you choose, it’s a good idea to take your old valve to the plumbing supply store so that you can find the right parts. Make note of the brand and model number to make sure you get the right parts. Your shower won’t work if you install the wrong type of valve and remember that your valve is specific to your faucet brand. For example, if you have a Delta faucet, you're going to need a Delta valve.

Put It Back Together

No matter which option you choose, your installation is going to be the reverse of your disassembly. Start by seating the gasket, use your pencil to push the grommets and springs into the valve body holes, and press and hold the valve in place. Make sure you’ve got the side of the valve labeled HOT oriented in the correct position (usually to the left) and tighten the bushing by hand. Give the bushing one very gentle twist with the strap wrench and then turn on the water. You should be able to test everything by twisting the valve stem by hand. Test your hot and cold water, and make sure your drips have stopped before moving on to the last step. If your hot water isn’t working, you might have the valve installed in the wrong orientation. If your shower still drips, you might not have your gaskets seated all the way inside the valve body.

Re-Install Trim

Remember that big rubber gasket we left alone in step 2? Now you’re going to need to roll it forward until it rests behind the valve bushing. Take your valve collar and push it over the valve body so that it rolls over that gasket. This will keep any errant drips from going into the wall, so make sure that the gasket is UNDERNEATH the valve collar. Next, simply screw the wall plate in place and re-install your faucet handle and you're all set.

Next Up

How to Install an Anti-Scald Valve

Stop sudden shower water temperature changes by installing an anti-scald valve in your shower.

Tips on Solving Common Toilet Problems

Master plumber Ed Del Grande explains how even the average homeowner can easily fix common toilet problems.

Euro-style Personal Hygiene With the Bidet

The bidet: What is this mysterious French lavatory fixture, and will it ever find a place in American bathrooms?

Let Nature in With an Outdoor Shower

Outdoor showers aren't just for poolside and public beaches anymore. They're fast becoming a refreshing addition to the everyday home bathroom.

10 Things You Must Know: Plumbing Leaks

You don't need to know everything about plumbing, but it's important to understand the basics, especially when it comes to leaks.

Tips for Bathroom Vanity Installation

10 things you must know about installing a bathroom vanity

Choose the Right Toilet for Your Bathroom

Size, height and function all play a role in selecting a toilet for a new bathroom. These tips will help you find the right commode for your family.

Bathtub Faucet Buyer's Guide

Today's bathtub faucets go beyond functional, with designs and styles available to fit any tub you choose. Understand your options first before hitting the showroom floor.

Tips for Setting up a Steam Shower Generator

DIY Network host Ed Del Grande offers tips for getting the process of installing a steam shower started.

Choosing a Bathroom Faucet

Swapping out old faucets for new is a simple way to make a big splash.


Get Social With Us

We love to DIY. You love to DIY. Let's get together.

Consult Our A-Z Guide

Everything You Need to Know

Browse a full list of topics found on the site, from accessories to mudrooms to wreaths.  

How-To Advice and Videos

Get video instructions about kitchens, bathrooms, remodeling, flooring, painting and more.

Watch DIY Downloads Now

Watch DIY Network LIVE

Don't miss your favorite shows in real time online.