Natural Cork Flooring

Installing and caring for natural cork flooring is simple with these tips.
installing natural cork flooring

installing natural cork flooring

Natural Cork Flooring

Natural Cork Flooring

Installing on Concrete Substrate

Cork parquet can be installed over concrete on or above grade. Concrete substrates are required to be sound, smooth, level and flat with a maximum variation of 1/8 inch in 10 feet. Subfloor should be free of dust, dirt and soils. Any uncorrected irregularities will telegraph through cork parquet tiles. All cracks, holes and control joints must be patched with a Portland cement based compound. Follow compound manufacturer's instructions fully and make sure patches are completely dry and well adhered. Use of gypsum base compounds is not approved. Check concrete slab for moisture. Slab must be properly cured. Check slab with calcium chloride moisture test. Moisture content cannot be more than three pounds per 1,000 sq. ft. per 24 hours.

Acclimating Cork Parquets

Store cork parquet tiles must be stored out of the box at job site for a minimum of 72 hours prior to installation. During storage and installation, maintain temperature and relative humidity to level consistent with conditions that will prevail when building is occupied. Heating or air conditioning should be used for an appropriate length of time prior to and during installation. With improper acclimation, the floor could noticeably expand or contract after installation.

Laying Cork Parquet Tiles

Use any standard laying pattern. For best installation, lay cork parquets with staggered joints. Shuffle cork parquets for best visual mix and identify possible manufacturing defects. Installer must accept liability for installing defective material. Mix cork parquets from various cartons to maintain natural color and pattern variation. Allow 1/4" expansion space between finished floor and all walls, thresholds, water pipes and other vertical surfaces. Failure to provide adequate expansion space will result in installation failure. When moisture level in the environment is low, parquet tiles should not be positioned too tightly against one another. To the contrary, when moisture level is elevated, tiles should be installed tightly. When cork parquet tile is properly aligned in place, apply pressure on entire parquet surface. Pressure will cause parquet to stick firmly and further movement will not be possible.

After Installation

Allow glue to set for at least 24 hours before walking on the floor. After 24 hours you may install molding, trim, transition pieces, and/or reducer strips as needed. If dried adhesive is found on the surface of the floor, it can be removed with a rag dampened with water-diluted mineral spirits.

Floor Cleaning

The entire floor must then be cleaned using a polyurethane cleaner. Mist over the floor using a spray bottle. Using a damp-dry mop, thoroughly clean the floor. Using too much liquid on your floor could provoke swelling at the joints due to absorption of moisture by the unsealed cork.

Floor Sealing

Moisture penetrating joints can eventually cause damage to the floor. Sealing your floor will prevent surface moisture penetration. This step is highly recommended for kitchens and other at risk areas. Natural Cork recommends using a high quality water base urethane.

Next Up

The Definitive Guide to Cork Flooring

Cork flooring has many specialized attributes — but is it the right choice for you?

How to Clean Cork Floors

Learn how to safely clean and seal a cork floor with these simple tips from DIY experts.

What You Need to Know Before Installing Laminate Flooring

Smart planning and prep make this DIY-friendly material even easier to install.

Carpet Thresholds

Get tips for installing threshold transitions between different types of flooring and carpet for a finished look.

What You Need to Know Before Starting a Floor Installation

Getting good results starts with an honest evaluation of your DIY skills.

Bamboo Floor Installation

Knowing some bamboo flooring pros and cons helps installation go smoothly.

What You Need to Know Before Installing Carpet

One of the biggest challenges of DIY carpet installation is getting everything ready for the job.

Where Should You Use Rubber Flooring?

Once considered novelty flooring, rubber flooring is finding wider acceptance for residential use.

What You Should Know About Installing Insulation

Save on utility bills by learning the basics of insulation installation.


Get Social With Us

We love to DIY. You love to DIY. Let's get together.

Consult Our A-Z Guide

Everything You Need to Know

Browse a full list of topics found on the site, from accessories to mudrooms to wreaths.  

How-To Advice and Videos

Get video instructions about kitchens, bathrooms, remodeling, flooring, painting and more.

Watch DIY Downloads Now

Watch DIY Network LIVE

Don't miss your favorite shows in real time online.