How to Make a Wooden Blanket Ladder

This easy blanket ladder project is the perfect handmade accessory for storing and displaying quilts and throws.

Related To:

'Tis the season to find all of the throw blankets you've had stashed in the back of the closet. With a DIY blanket ladder, you'll satisfy organizational needs and also create a lovely display for your home. Customized to hold as many throws as you desire, this wooden accessory is one you'll want to cozy up near all winter long.

How to Make a Blanket Ladder

How to Make a Blanket Ladder

How to Make a Blanket Ladder

Photo by: Emily Fazio

Emily Fazio

Materials + Tools

  • (2) 8' 2x4 premium boards
  • (2) 4' 1-1/4” wood dowels (more if you are building more than four rungs)
  • clamps
  • drill
  • 1-1/4” drill bit (paddle bit or a similar product)
  • measuring tape
  • speed square
  • wood glue
  • miter saw
  • palm sander
  • stain (optional)

Measure for Holes

Attention to detail and precision are undeniably important when you're building a "ladder." When you're selecting your premium boards, be attentive to how evenly the boards are cut. Check for unsightly knots (not as common when you're sourcing high-quality wood). Be sure the boards aren't warped. (Image 1) Layer the two boards together on your workbench and clamp them together. The ladder built here was designed to be 80 inches tall, with four evenly spaced rungs at the 16-inch, 32-inch, 48-inch, and 64-inch points (You might see these measurements differentiated on your measuring tape, as that's the common spacing for wall studs)(Image 2). Use the measuring tape and a speed square to mark each of the four dowel holes to be cut on-center along the length of the board.

Drill Holes for the Dowels

The holes for the dowels need to align perfectly in order to be level and to make it easy to assemble — one of the reasons the boards are clamped together (Image 1). Use a drill and bit to begin drilling the holes for the rungs. Important tip: Only drill about 3/4 of the way through the top board. The reason not to drill straight through both boards in one quick motion? When the drill bit exits the bottom board, it's possible the wood will splinter. Splintering wood is easier to avoid if you happen to have a drill press and Forstner bits, but I don't, and I'm happy to say that my method was an easy workaround, assuming your workshop is also quite simple.

When you've drilled 3/4 of the way through the top board along all four markings running the length of the board, put down the drill and unclamp the two boards. Flip the top board and you should see a tiny hole where the tip of your drill bit poked through the other side (Image 2), and observe that the bit also marked the top of the second board as well. You've transferred your marks correctly and now you can continue cutting the holes for your dowels.

No need to re-clamp the boards (unless you wish to secure them to a workbench). On the board that was previously on top, flip it and use the drill to bore through the marked hole to clear away a perfect (not splintered) hole for your dowels (Image 3). Repeat this process on the second board (Image 4). Following the marks you transferred, cut 3/4 of the way through the board so that you can see the tip of the drill bit beneath the board, and then flip it and complete the process.

Trim Feet

If your ladder is also 80 inches, know that a 10-degree angle is what I used when I cut my feet. Height will affect the cut you make, so start with a smaller angle, and cut away more until you're confident that the ladder stands securely at an appropriate (and expected) angle against the wall.

How to Make a Blanket Ladder

How to Make a Blanket Ladder

How to Make a Blanket Ladder

Photo by: Emily Fazio

Emily Fazio

Trim Dowels

Trim both 48-inch dowels in half, and then align the four pieces and make one additional cut to remove the rough ends of the dowel. Sometimes these ends are painted or nicked, and fresh ends look better, especially because they'll all be exposed. All four dowels should measure 22 inches.

How to Make a Blanket Ladder

How to Make a Blanket Ladder

How to Make a Blanket Ladder

Photo by: Emily Fazio

Emily Fazio

Assemble the Ladder

No hardware is required for this ladder — did you notice that in the materials list? The only product I used to assemble the ladder was wood glue.

Begin by applying a thin coat of wood glue along the holes on one board (Image 1). I stress applying a thin coat because wood glue goes a long way. Use your finger or a small paintbrush to control application. Also, apply a thin layer of glue around the lower 1/2-inch of the dowels (not on the ends) and insert them one at a time into the board as it lays on the workbench. Because the dowels and drilled holes are all 1-1/4 inches, the fit should be pretty tight (Image 2). You may need to twist the dowels to get them in position. Monitor how far the dowel is emerging through the underside of the board. Try to get it flush or ever-so-slightly emerging (it can be sanded down). With the dowels positioned vertically, prep the other board and the ends of the dowels with wood glue and help the pieces align (Image 3). Again, if the fit is so tight that it needs a little help, use a rubber mallet cushioned by a piece of natural wood (it helps to distribute the force and soften the blow, and protects against any marks that may be left by the mallet). Allow the wood glue to dry.

Sand and Stain (If You Wish)

Use a palm sander along the rails of the ladder to smooth out any imperfections. Once it's smooth, apply stain if you wish, or a coat of water-based clear polyacrylic to seal the wood.

How to Make a Blanket Ladder

How to Make a Blanket Ladder

How to Make a Blanket Ladder

Photo by: Emily Fazio

Emily Fazio

Add Rubber to the Feet

If you have any concerns about the ladder sliding, trim a small rubbery piece to attach to the underside of each foot. A cushioned drawer liner or piece of thin rug pad works well. Avoid felt and fabric.

Adorn With Blankets

Cozy up to a new way of displaying your favorite blankets! (Love that golden knit throw? I made it! Learn how to arm knit one of your own.)

How to Make a Blanket Ladder

How to Make a Blanket Ladder

How to Make a Blanket Ladder

Photo by: Emily Fazio

Emily Fazio

Next Up

How to Make a Decorative Pegboard Shelf

Need wall storage but can’t find just the right shelving unit? Try this modern take on an old-school storage idea. It’s easy to build and you can customize the colors however you’d like.

How to Build a DIY Kitchen Island on Wheels

Need some extra workspace in your kitchen? Build a rolling island for added functionality and style. One side stores a stand mixer, sheet pans, cutting boards and more, while the other side allows for extra seating. Perfect for small spaces, this portable kitchen island easily rolls out when you need it and neatly tucks away when you don’t.

How to Refinish Wood Furniture

Follow these simple steps on how to refinish wood furniture that include stripping, sanding and staining.

Easy Woodworking Project: Build Storage Shelves for the Garage

Keep tools and equipment organized with these easy-to-build shelves. The design is simple yet sturdy and the pegboard supports mean the shelves can easily be adjusted.

Here's How to Get Organized, Based on Your Zodiac Sign

Look to the stars for more structure in your life.

How to Make Exterior Wood Window Shutters

Refresh your home's curb appeal with these easy-to-build board-and-batten-style cedar window shutters.

30 Over-the-Toilet Storage Solutions That Are Actually Stylish

Create more storage in a bathroom without sacrificing space or style.

11 Stylish Organizers for Storing Glasses and Sunglasses

Whether you're looking to store a single pair of glasses, multiple frames or over a dozen shades, streamline your storage and protect your frames with one of these stylish organizers.

How to Paint a Wooden Outdoor Barn Quilt

Looking to add color and style to your porch or patio? Check out how easy it is to make a decorative quilt barn to hang in your outdoor or indoor space.

This Woodworking Couple Gives New Life to Salvaged Wood With Custom Furniture

Get to know the makers behind the sustainable, Tacoma woodworking studio Birdloft. Then shop our favorite custom-made pieces.

What's New in Handmade

On TV

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.