How to Drain a Water Heater

Extend your water heater's life span by draining the tank annually to remove any sediment that may have built up.

Most water heaters employ a large, insulated holding tank to ensure there's plenty of hot water on hand at all times for different purposes throughout the home. Over time, naturally occurring minerals in the water, as well as sand and grit flushed from municipal water lines, can settle in the bottom of the tank. This sediment buildup can potentially reduce the efficiency and capacity of your water heater. It can also plug the drain and interfere with ongoing maintenance, leading to early failure. Draining a water heater to remove sediments is an easy DIY that takes very little time and just a few basic tools.

A standard tank hot-water heater.

Hot-Water Heater

Over time, naturally occurring minerals in water, as well as sand and grit flushed from municipal water lines, can settle in the bottom of your home water heater tank. Sediment buildup can potentially reduce the efficiency and capacity of your water heater.

Photo by: Sherri James

Sherri James

Over time, naturally occurring minerals in water, as well as sand and grit flushed from municipal water lines, can settle in the bottom of your home water heater tank. Sediment buildup can potentially reduce the efficiency and capacity of your water heater.

How Often Should You Drain a Water Heater?

Sediment can interfere with burner efficiency in a gas water heater and can cause cracking and popping noises during heating cycles. Depending on your water source and the mineral content, both gas and electric water heaters should be flushed of sediment every one to two years to ensure optimal performance.

Dave Moody, a plumbing pro with Service Experts, suggests, "You may need to drain your water heater more frequently if your water source is a well or if your municipal water has higher-than-normal sediment content."

1. Turn Off Water Supply

Turn off the cold water supply valve at the top of the water heater.

The cold water supply valve will be clearly marked on the top of the water heater and should have a blue handle.

The cold water supply valve will be clearly marked on the top of the water heater and should have a blue handle.

2. Turn Off the Water Heater

Turn the thermostat to the "pilot" setting (gas) or shut off the power at the breaker box (electric).

Note: Electric water heaters must be turned off completely during flushing. Exposed heating elements can burn out quickly if the water level in the tank drops below the level of the hot elements.

Most electric water heaters are wired directly to their own circuit breaker. Find the water heater's breaker switch in the main electrical panel.

"Even with the gas burner or electric heating elements turned off, water in a water heater tank may remain scalding hot for hours," Moody warns. "Either wait overnight for the water to cool before proceeding, or take extreme caution to drain the scalding hot water away from where it may cause harm."

3. Attach Hose to Drain Valve

Near the bottom of the tank, locate the tank's drain valve and attach a standard garden hose to the valve. Be aware that some models may have a cover over the valve opening. Place the other end of the hose in a floor drain or on a driveway where it can drain safely. If necessary, buckets can be used, but be careful not to be burned by the hot water as you work.

Near the bottom of the tank, locate the tank drain valve and attach a standard garden hose to the drain valve.

Near the bottom of the tank, locate the tank drain valve and attach a standard garden hose to the drain valve.

4. Open Hot Water Tap

Open a hot water tap nearest to the water heater, preferably on the floor above. This alleviates pressure in the system, allowing the water to drain quickly from the tank, much like removing your finger from the top of a drinking straw filled with liquid.

Open a hot water tap nearest to the water heater, preferably on the floor above. This alleviates pressure in the system, allowing the water to drain quickly from the tank, much like removing your finger from the top of a drinking straw filled with liquid.

Open a hot water tap nearest to the water heater, preferably on the floor above. This alleviates pressure in the system, allowing the water to drain quickly from the tank, much like removing your finger from the top of a drinking straw filled with liquid.

5. Open Drain Valve

Open the drain valve and allow the water to drain from the tank. On many models, you can do this with a flathead screwdriver. Again, the water will be hot, so use caution. Once all water has drained from the tank, briefly turn on the cold water supply to the tank. This will stir up any remaining sediment.

Some drain valves will require a screwdriver to open.

Some drain valves will require a screwdriver to open.

Repeat this process until the water runs clear. Dave Moody has seen some severe cases of sediment buildup: "In some cases, sediment may block the opening of the drain valve, limiting the flow of water. If this happens it's best to call in an expert for assistance."

6. Close Valve, Refill Tank, Restart Water Heater

Close the drain valve, remove the hose and turn on the cold water supply. The tank will begin to fill. Go back to the hot water tap opened earlier. Once cold water begins to flow from the tap, turn it off. Turn the gas valve back on from the pilot position or turn the electricity back on to the tank. Be sure to check the valve opening once it's closed to ensure there are no water leaks.

Caution: Some tanks must be completely full to avoid damage to the gas burner or heating elements. Always read and follow all manufacturer's directions and warnings for your particular water heater.

Hot-Water Heater Buying Guide

Learn about the different types of hot-water heaters, which are the most energy efficient and how to get money back in federal tax credit.

Next Up

How to Increase Your Home's Water Pressure

Don't let poor low water pressure in your house get you down. Take these steps to test water flow around your home and begin to identify the cause of the issue.

How to Install a Garbage Disposal

Say goodbye to smelly food scraps and hello to a new garbage disposal.

How to Clean a Computer Screen

Get the low-down on how to safely remove dust, fingerprints, smudges and streaks from any type of laptop screen or computer monitor.

How to Prevent Pipes From Freezing in the Winter

Follow these tips to prevent bursting water pipes during cold spells.

How to Get Rid of Thrips

Thrips can damage your plants before you even know they’re there. Here’s how to spot thrips on plants and get rid of them.

How to Repair a Burst Pipe

Learn how to repair a broken pipe using a soldering kit or push-to-connect fittings.

6 Easy Ways to Unclog a Toilet Without a Plunger

Tips for taking care of, ahem, business. Learn how to clear a clog without a plunger.

6 Ways to Humidify Your House (Without a Humidifier)

During the winter months, low humidity in your home can become an issue, leading to worsening allergies, dry skin, static electricity and increased susceptibility to colds and flu. Find ways to add moisture to the air without the expense of buying and running a humidifier.

How to Wire a Light Switch

Electricity is a mystery to many people, but some electrical projects — like wiring a switch — are so simple that anyone can do them. With a few easy steps and the right knowledge, there’s no need to hire an electrician.

How to Sharpen a Knife

Learning to sharpen your knives at home will keep them razor-sharp, making them safer and easier to use.

Go Shopping

Get product recommendations from HGTV editors, plus can’t-miss sales and deals.

On TV

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.