HOME IMPROVEMENT Index
Appliances
Basement
Bathrooms
Bedrooms
Cleaning
Contractors
Doors
Driveways & Paths
Duct Tape
Electrical Systems
Family Room
Fences & Gates
Fireplace
Floor Coverings
Furniture
Handles, Knobs & Hinges
Help on the Homefront
Home Energy Efficiency
Home Office
Homeowner in Process
House Exterior
Indoor Pests
Kitchens
Lighting
Outdoor Equipment
Outdoor Structures
Painting
Plumbing
Safety
Sports-Related Additions
Staining
Stairs
Storage
Cabinets, Closets & Shelves
Custom
Drawers
Organizers
Wine Cellar
Other

Tools
Utility Room
Walls & Ceilings
Windows

BEST OF
HOME IMPROVEMENT
Flooring
Decks
Mold Quiz
Home Safety
Tiling Techniques
Lighting Solutions
Weekend Projects
DIY to the Rescue
Home Renovations
Bathroom Makeover
Kitchen Renovations
Ultimate Media Room
Be Your Own Contractor

SPONSOR LINKS

  • Wine Rack
  • From "DIY Home Repair & Remodeling"
    episode DIR-163
    advertisement

    Click here to view a larger image.

    Figure A

    Click here to view a larger image.

    Figure B

    Click here to view a larger image.

    Figure C

    Click here to view a larger image.

    Figure D

    Click here to view a larger image.

    Figure E

    Click here to view a larger image.

    Figure F

    Click here to view a larger image.

    Figure G

    Click here to view a larger image.

    Figure H

    Click here to view a larger image.

    Figure I

    Click here to view a larger image.

    Figure J

    You can buy a variety of wine-glass racks in a wide range of prices. One kind that hangs from the ceiling (figure A) can be enhanced to include a wine rack.

    Materials:

    1" x 4" boards
    Table saw
    Drill, with drill bits
    Hammer
    Finish nails
    Wood glue
    Decorative chain
    Eye hooks with matching cap nuts
    Corrugated roofing-support material
    Safety glasses

    1. The wine rack will be made of six 14"-long 1" by 4" boards cut so they have angled "shoulders" (figure B). To create these angled boards, set a table-saw blade to face 26 degrees away from the fence (figure C ), and run the boards through on their sides. To create pieces for the ends, cut a shoulder section off each end piece (figure D).

    2. Make a reference mark 1" from the front end of each board (figure E).

    3. Rip a 1" by 4" board down to a 1" strip. Lay the boards side by side, and lay the 1" strip across them so it lines up behind the reference mark. The strip should hang over the ends by about 1" (figure F). The space between the slats should be 1 1/2". Mark the proper spacing for the slats on the 1" strip of wood. This will help you align the slats properly.

    4. Secure the strip to the slats with wood glue and finish nails. Use two nails for each slat.

    5. Lay another 1" strip of wood across the slats on the back end of the rack. Position the strip so it's about 1" away from the edges of the slats (figure G). Glue and nail the strip into place as before.

    6. Cut two pieces of corrugated roofing-support material 18 1/2" long. Measure and mark the center of the corrugated strip, and mark the center of the 1" strip of wood you placed on the slats. Run a bead of wood glue on the top of the 1" strip, and place the corrugated material onto the strip so the center marks line up (figure H). Repeat the procedure for the other 1" strip.

    7. Drill holes into the ends of the 1" strips, and insert eye hooks (figure I). Secure the eye hooks with cap nuts.

    8. Attach decorative chains (available at home-improvement centers) to the eye hooks (figure J) so you can suspend the rack from the ceiling.

  • ALSO IN THIS EPISODE: