| Installing a Banquette: Install the Doors and Bead Board |
From "Weekend Remodeling"
episode WKR-113 |
|
|
|
advertisement
|
Prep Work, Build Base, Redirect Air Vent, Relocate Electrical Outlets and Attach Top to Base = 3 hours
Build Frame for Bench Seating, Build Facings for Door Openings and Install Top = 4 hours
Install the Doors and Bead Board = 4 hours
Install Chair Rail, Quarter Round and Decorative Half Round Trims and Paint Trim = 4 hours
Total time spent = 15 hours over 2-1/2 days On a scale of 1 to 5, with 5 being the hardest, this project is a 3. Approximately $700 was spent on supplies; a contractor would charge approximately $1,500. Materials: Power nailer (rented)
Utility knife
Prybar
Primer, good paint and brushes
Compound miter saw
A/C diverter
Chair rail wood trim
Quarter round trim
Decorative half round molding
Birch plywood
Circular saw
Miter saw
2 x 4's
Hammer
Chisel
Nail gun
Premade floor air vent
Duct tape
Silicone
Electric drill and bits
Wood screws
2 x 2's
Jigsaw
Cabinet decorative end panels
Construction adhesive
Painters tape
Door panels with circular cutouts precut for hidden hinges
Hidden hinges for each door
Bead board
Caulk and caulking gun
Wood putty - If possible, purchase two decorative end panels that match your kitchen cabinets for the ends of the cabinet. Generously apply construction adhesive on the backs of the end panels. Just apply the adhesive in the center area of the panel only ( figure A). You do not want to excessive adhesive at the edges.
- Place the panel on each side of the ends of the seating (figure B). Hold the panel in place, and do not let it move as you place painters tape around -- making sure it is nice and tight Leave the tape on until the adhesive completely dries.
- Apply the hidden hinges to the back of the door panels (panels that have the precut circular hole).
- Place the hinge into the hole and make sure it is straight and then screw the hinge in place (figure C).
Note: It is easier to predrill a hole on finished cabinets before you screw the hinges in place. - Cut a 2 x 4 to the height that you want to install your doors to use as a guide (figure D). Mark the wood where the screws will go and then screw the hinges in place. Use the adjusting screws on the hinges to make any minor changes in leveling the doors.
- Once the doors are up, install the hands. First, use a nail to make an indention on the face of the door so the drill bit won't scratch the finish (figure E). Once you have predrilled the holes, install the handles.
Expert Tip: Once you get all your cabinet doors installed and adjusted, it is always a good idea to step back a couple of feet to get an overall perspective. If all your doors are level and your doors are parallel, you have done a good job. - To define the seating area, add bead board along the walls. Once you determine the desired height you want the bead board to be, measure for the first piece and cut it with a circular saw. Measure the first piece beside your first window. Put construction adhesive on the back and place the bead board on the wall and press it to smooth the adhesive out. Nail it in place on the corners (figure F) and the edges. Work your way from the window to the nearest end and then continue around the wall -- this will make it easier to fit the first corner together. The pieces will butt up next to each other as you move around the wall. Do one panel at a time -- measure, cut, glue and nail all the way around.
- At the corners, miter the joints just as you did for the base and seat top. Cut the bead board on a 22-1/2 degree angle to make everything fit as close as possible.
Expert Tip: Whenever you are cutting decorative paneling or any type of sheeting with a finished side, turn the finished side down. By doing this, the saw blade will pull towards the backside and any splintering will be hidden. - You can't precut the bead board ahead of time, but is worth it when the last board goes up.
- After installing the bead board, countersink any nails sticking up, putty the nail holes, caulk along the seams and give it a good coat of paint.
RESOURCES :
Waverly Fabrics
Website: www.waverly.com
Terence Conrad Kitchens: The Hub of the Home
ISBN: 060961052X
Author: Terence Conrad
Order this title from Amazon.
Clarkson Potter/The Crown Publishing Group/Random House
Website: www.randomhouse.com
| 
)
)
)
)
)
)
)
