DIY Network

Best of Both Worlds (3 of 3): Vent Hood Installation From "Kitchen Renovations" episode DKTN-303

	In our three-part "Best or Both Worlds" kitchen renovation, host Paul Ryan works with homeowners Steve and Michelle to convert the "before" kitchen you see here ...
	into an updated kitchen that is the best of both worlds.
	In this final episode Ryan helps the homeowners install their new high-tech range hood and ...
	install the acrylic panels in the cabinet doors.
	They finished the kitchen by installing a new faucet.

Materials:

For Vent Hood Installation --

Safety glasses
Pencil
Tape measure
Screw gun
Nut Driver
Utility knife
Pliers
Screwdriver

For Refacing Drawers --

Table saw
Tape measure
Pencil
Clamps
Drill
Screw gun

For Door Hinges --

Straight edge
Drill

For Lumicor Inserts --

180-tooth steel saw bridge
Table saw
Rosin paper
Tape
Glazing points
Putty knife

For Faucet Installation --

Tape
Tape measure
Pencil
Drill
Hole saw

advertisement

	Figure A
	Figure B
	Figure C
	Figure D
	Figure E
	Figure F
	Figure G

1. Steve and Michelle (our homeowners) had a HVAC professional install the ductwork and the support frame bracket (figure A).

   
   

2. The installation template comes with the hood. Cut out the template and place it over the vent and mark the screws for the support frame bracket (figure B).

   
   

3. Drill the pilot holes in the ceiling for the mounting bracket. With the wiring attached to the support frame, raise it to the ceiling and secure it to the bracket with lag bolts and washers (figure C).

   
   

4. Attach the electrical plate system to the blower support. Secure the duct collar to the blower support (figure D), and attach the support frame to the blower support.

   
   

5. Determine the distance between the hood filter and cook top according to the chart that comes with the instructions.

   
   

6. Unscrew the support frame, adjust the frame, and then screw it back together.

   
   

7. Assemble the support frame on the blower (figure E) so you can cover it with the decorative flue. In order to do that, you need to thread the control panel that is attached to the power cord through the stainless flue and then screw it in place.

   
   

8. Feed through the low voltage lighting wires and tape them down.

   
   

9. Carefully lift the decorative flue over the support frame, lower the flue into position, and then raise up the decorative flue. Attach the duct to the vent blower.

   
   Safety Tip: Be careful when working with aluminum tape. The edges are sharp!

   
   

10. A few bolts secure the support frame to the blower. Run the power -- it is basically like wiring a ceiling fan.

    
    Note: If you are unsure about wiring, hire a professional.

    
    Lift the vent into place (it weighs approximately 50 pounds) and feed the ductwork at the same time. Telescope the flue for your final connection.

    
    

11. Last of all, you install the light kit. The support rods that support the lights are part of the wiring itself. Start with the metal bar assembly by taping it to the electrical connector (figure F) and then guide it into the hole on the flue.

    
    

12. Slide the insulator up to the flue and connect the bottom bar to the support post (figure G), making the connection.

    
    

13. Once you are ready for the lights, just put the lamp between the metal bars and move it to the desired spot and then install the adjustment slide screws and tighten them with the hex key provided with the kit.

In the next segment, the kitchen drawers are refaced and the hardware installed on the doors.

RESOURCES :

Flat Panel Cabinet Doors
Color: Cherry
Where available: Visit the AJS Woodworking LTD website, link below.
AJS Woodworking LTD
Website: www.kitchendoordepot.com

Oval Leaves Acrylic Panels
Brand name: Lumicor
Model #: AB-803-101
Color: White/Translucent
Where available: Visit the Designtex website, link below.
Designtex
Website: www.lumicor.com

Spray Finish on Cabinet Doors
Brand name: Plastifix
Color: Clear, 35 degree sheen
Where available: See Roe's International Furniture website, link below.

Clear Catalyzed Lacquer
Where available: See Roe's International Furniture website, link below.

Stain and Clear Lacquer
Where available: See Roe's International Furniture website, link below.

Roe's International Furniture
2303 Kennedy NE
Minneapolis, MN 55413

Single Scroll Knob
Brand name: Atlas
Model #: 102
Color: Craftsman Copper
Where available: Visit the Atlas Homewares website, link below.

"S" Scroll Pull
Brand name: Atlas
Model #:102
Color: Craftsman Copper
Where available: Visit the Atlas Homewares website, link below.

Atlas Homewares
Website: www.atlashomewares.com

Island Range Hood
Brand name: Best by Broan
Model #: IS502
Color: Stainless Steel
Where available: Visit the Broan-NuTone website, link below.
Broan-Nutone
Website: www.broan-nutone.com

Decorative Screening Panels for Sink Cabinet Facing
Model Number: RC25
Color or type: Hardboard (Natural)
Where available: Visit the Outwater website, link below.
Architectural Products by Outwater
Website: www.outwatercatalogs.com

Michael Graves Kitchen Faucet
Brand name: Delta Faucet Company
Model #: 187-MCWF
Color: Matte Chrome
Where available: Visit the Delta Faucet website, link below.
Delta Faucet Company
Website: www.deltafaucet.com

Pro-Style Dual Fuel Slide-In Range
Brand name: Jenn-Air
Color: Stainless Steel
Model #: JDS9860AAP
Where available: Visit the Jenn-air website, link below.

Pro-Style Built-In Dishwasher
Brand name: Jenn-Air
Color: Stainless Steel
Model #: JDB6510AWP
Where available: Visit the Jenn-air website, link below.

23cf Counter-Depth Side-by-Side Refrigerator
Brand name: Jenn-Air
Color: Stainless Steel
Model #: JCD2389GES
Where available: Visit the Jenn-air website, link below.

Built-In/Countertop Microwave Oven
Brand name: Jenn-Air
Color: Stainless Steel
Model #: UMC5200AAS
Where available: Visit the Jenn-air website, link below.

Jenn-Air
Website: www.jennair.com