 |

 In this week's episode of Kitchen Renovations, host Paul Ryan will assist the homeowners in converting this antiquated kitchen ...
|
|  |

 into this kitchen that would be any chef's delight, ...
|
|  |

 with top-of-the-line, professional-style appliances!
|
|  |

 In this week's episode, host Paul Ryan and the homeowners will install custom-built cabinets, which have an alder color and Ipswitch pine finish, ...
|
|  |

 and a stainless-steel countertop that is perfect for our resident chef!
|
|
In this third segment we're ready for the countertops. First is a stainless-steel countertop for the sink and prep area, which is installed by professionals. For the other side of the room, a granite accent counter is brought in.Materials: Installing Cabinets -- Custom cabinets Trim molding Tape measure Level Stud finder Pencil Drill Cabinet lift Screw gun 2-1/2" deck screws Clamps Shims Hammer Impact driver Spade bit Riser blocks Installing Stainless-Steel Countertop -- Countertop Drill Spade bit Jigsaw Construction adhesive Installing Granite Countertop -- Silicone Installing Porcelain and Metal Tile -- Tile 3/8" square-notched trowel Thin set Wet saw Rosin paper Masking tape Spacers Silicone caulk Attaching Cabinet Doors -- Cup hinges Level Screw gun Vix bit Screws
Stainless Countertop Installation- Dry fit countertop to make sure it fits, and if it's a good fit lift the countertop up and out.
- Measure and mark the hole needed for the sink, and use a drill with the spade bit to make the starter hole (figure A).
- Now take the jigsaw and cut out the marked area needed for the sink.
- Now apply a bead of construction adhesive on the top edge of the cabinet boxes (figure B). This will hold countertop in place.
- Set countertop into place (figure C).
Granite Countertop InstallationNote: The homeowners chose to go with a granite countertop on the other side of the kitchen from the stainless countertop. - Do a dry fit first (always) to make sure the piece fits.
- Now apply a bead of silicone around the top edge of cabinet box.
- Set the granite countertop in place (figure D).
In the next segment learn a lesson in tiling as Ryan and the homeowners tile the backsplash and soffit.
RESOURCES :
Skil
Robert Bosch Tool Corp.
Website: www.skiltools.com
Stanley Tools Information
Stanley Tools/Works
Website: www.stanleyworks.com
Fiskars (Bucket Boss Division) Fiskars Bucket Boss Division
Website: www.bucketboss.com
Makita Products Makita USA Inc.
Website: www.makita.com
Paslode Nail Guns
Paslode
Website: www.paslode.com
3M Painter's Masking Tape and Sanding Pad The 3M Company
Website: www.3m.com
Custom Kitchen Cabinets (Minnesota Valley Cabinets)
Color: Red Alder
Minnesota Valley Cabinets
Website: www.minnesotavalleycabinets.com
Paint (Behr) The Home Depot
Website: www.homedepot.com
Spray Paint (Rust-Oleum) Rust-Oleum Corp.
Website: www.rustoleum.com
Cabinet Doors and Molding (Fleetwoods)
Style: Flat-panel doors, slab drawer fronts and crown molding
Color: Alder
Where available: Visit the Fleetwoods website, link below. Fleetwoods
Website: www.fleetwoodsinc.com
Custom Stainless Steel Countertop with Integral Sinks and Marine Edge
Color: 304 #4
Where available: Can ship nationwide, call 651-765-9004. Custom Stainless Steel
3775 Lexington Ave. N
Arden Hills, MN 55126
Phone: 651-765-9004
Fax: 651-765-9006
Tiles
Brand: Questech line
Country Bright Satin (SBN, 6x6, Model # 114-005-003)
Riveted Plates Polished (6x6, Model # 210-005-0010
Interior Wall Trim Diamond Plate Bright Satin (3/4"x12", Model # 292-005-003)
Vermont Line (Trail Green, 12x12, Model # AV62)
Where available: Visit the Crossville Porcelain Stone website, link below. Crossville Porcelain Stone
Website: www.crossvilleinc.com
Cabinet Hardware
Full Extension Drawer Slides (Brand name: Accuride, Model # 02K10.22)
Square Shell Drawer Pulls (Model # 01A57.40)
Antique Nickel Double Reed Knob (Model # 02A14.50)
Where available: Visit the Lee Valley website, link below. Lee Valley Tools. Ltd.
Website: www.leevalley.com
GUESTS :
Shane Kretsinger
Vice President, Operations
Autumn River
We apologize no contact information is available.
Bob Kroening
President, Custom Stainless Steel, Inc.
3775 Lexington Ave. N
Arden Hills, MN 55126
Phone: 651-765-9004
|