DIY Network

Turn-of-the-Century (3 of 3): Installing the Copper Backsplash From "Kitchen Renovations" episode DKTN-204

	Paul Ryan, host of Kitchen Renovations, starts a three-part project to convert this out-of-date kitchen...
	in a house that the homeowners are restoring ...
	into an authentically recreated Victorian kitchen ...
	complete with period appliances and ...
	new counters!

In this segment plywood is brought in to prep for the copper backsplash. The plywood is glued to the wall and the copper backsplash is nailed in.

Materials and Tools:

For Prepping the Sink Cabinet--

measuring tape, level, shims, silicone, caulk gun, 2" x 4" support block, 3" nails, impulse framing nailer

For Countertop Installation--

helpers, sandpaper, silicone, caulk gun

For Modifying and Cutting the Soapstone--

safety glasses, tablesaw with guide, diamond blade

For Prepping the Soapstone Joints--

safety glasses, tape, level, shims, 2-part epoxy, silicone, caulk gun, small putty knife, Soapstone dust, orbital palm sander

For Installing the Backsplash--

silicone, caulk gun, 2-part epoxy

For Installing the Copper Backsplash--

safety glasses, gloves, 1/4" plywood, sheets of copper backsplash, pencil, Dremel tool with carberundum cutting wheel, copper nails, drill, vix bit, hammer, caulk gun, silicone

For Trimming the Copper--

safety glasses, chop saw, chair rail trim material, mold cover trim material, tape measure

For Sealing the Countertops--

mineral oil, clean lint-free cloth

For the Appliance Installation--

helpers, dolly

advertisement

	Figure A
	Figure B
	Figure C
	Figure D
	Figure E

Installing the Copper Backsplash

This particular backsplash (figure A) is going to an eye-catching addition to this beautiful turn-of-the-century kitchen. And installing it isn't that difficult.

Note: The copper will attached to pieces of plywood.

1. Measure and cut pieces of 1/4" plywood for the area that will be covered with copper backsplash. Make sure to cut the holes for electrical boxes and faucet as well.

2. Dry fit the pieces (figure B).

3. Transfer the cutouts to the back of the first copper sheet. Do this by laying the plywood on top of the backside of the copper sheet and tracing the holes with pencil.

4. Cut the marked areas using a tool with a carbarundum cutting wheel (figure C). Please be sure to wear safety goggles when cutting metal.

5. Apply construction adhesive to the back side of the plywood, and stick the plywood to the wall.

6. Apply construction adhesive to the back of the copper backsplash as well -- a dollop in each square and set it to the wall.

7. Overlap the next piece about 1/2" (figure D) so the pattern will match.

8. Now use the special copper nails to finish off the backsplash. Drill pilot holes through the copper for the nails. Be careful nailing because copper is soft and will dent easily.

9. To trim the copper backsplash, measure and cut pieces of trim and mold cover, and nail into place using an impulse finish aniler and 1-1/2" nails (figure E).

In the final segment the final touches are applied, including the lighting and appliance installations.

RESOURCES :

Stanley Tools Information
Stanley Tools/Works
Website: www.stanleyworks.com

Fiskars (Bucket Boss Division)
Fiskars Bucket Boss Division
Website: www.bucketboss.com

Makita Products
Makita USA Inc.
Website: www.makita.com

Paslode Nail Guns
Paslode
Website: www.paslode.com

3M Painter's Masking Tape and Sanding Pad
The 3M Company
Website: www.3m.com

Soapstone Sink and Counter (Vermont Soapstone Co.)
Sink Model: Wright
Vermont Soapstone Co.
Website: www.vermontsoapstone.com

Copper Backsplash (Abbingdon Affilitates)
Brand name: Prestplate
Model #: 209
Color: Solid copper
AA Abbingdon Affiliates, Inc.
Website: www.abbingdon.com

Lighting, Switches and Switchplates (Rejunevation)

Product: Three Forks Wall Bracket
Model #: W880, with shade 139A
Color: Mottled brass

Product: Mt. Tabor Ceiling Fixture
Model #: C229-3 with shade 139A
Color: Mottled brass

Product: Regular Single Push Button Switch
Model #: 3706

Product: Regular Push Button Dimmer Switch
Model #: 5405

Product: Coverplat4e for Single Push Button Switch
Model #: 5700
Color: Mottled brass

Where available: Exclusively through Rejunevation, see contact information below.

Rejuvenation
Website: www.rejuvenation.com

Dixmude, Wall-mount Faucet and Garbage Disposal Flange (Herbeau Creations)
Faucet brand name: Herbeau
Model #: 420459
Color: Weathered copper / brass

Garbage disposal flange brand name: Herbeau
Model #: 451370
Color: Weathered copper / brass
Herbeau Creations
Website: www.herbeau.com

Antique-Styled All-Gas Range and Side-by-Side Refrigerator (Elmira Stove Works)
Range model #: 1960
Color: Black

Refrigerator model #: 1897
Color: Black
Elmira Stove Works
Website: www.elmirastoveworks.com

Microwave (Haier America)
Model #: HMOGR750B
Color: Black
Haier America
Website: www.haieramerica.com

GUESTS :

Shane Kretsinger
Vice President, Operations
Autumn River
We apologize no contact information is available.

Tony Hall and Mike Hall
Flooring Installers
Floor Design
2804 North Fairview
Roseville, MN 55113
Phone: 651-635-9924
Website: www.floordesign.com

Glenn Bowman
President
Vermont Soapstone
PO Box 268
Stoughton Pond Rd.
Perkinsville, VT 05151
Phone: 802-263-5404