HOME IMPROVEMENT Index
Appliances
Basement
Bathrooms
Cabinets & Shelves
Faucets & Fixtures
Remodeling
Sinks & Vanities
Surround
Tiles & Grout
Toilets, Tubs & Showers

Bedrooms
Cleaning
Contractors
Doors
Driveways & Paths
Duct Tape
Electrical Systems
Family Room
Fences & Gates
Fireplace
Floor Coverings
Furniture
Handles, Knobs & Hinges
Help on the Homefront
Home Energy Efficiency
Home Office
Homeowner in Process
House Exterior
Indoor Pests
Kitchens
Lighting
Outdoor Equipment
Outdoor Structures
Painting
Plumbing
Safety
Sports-Related Additions
Staining
Stairs
Storage
Tools
Utility Room
Walls & Ceilings
Windows

BEST OF
HOME IMPROVEMENT
Flooring
Decks
Mold Quiz
Home Safety
Tiling Techniques
Lighting Solutions
Weekend Projects
DIY to the Rescue
Home Renovations
Bathroom Makeover
Kitchen Renovations
Ultimate Media Room
Be Your Own Contractor

SPONSOR LINKS

  • Glass Tile Backsplash
  • Set off the vanity with classy glass.
    From "Bathroom Renovations"
    episode DBTR-506


    Beautiful glass tile makes a memorable backsplash – and will look great with the art glass sink Amy Matthews will install later. The technique for tiling with glass is slightly different than for ceramic tiles; Amy shares a few insider tricks.

    advertisement


    PHOTO

    The tile backsplash should extend slightly higher than the faucet.
    Materials:

    glass tile
    tape measure
    painter’s tape
    white tile adhesive
    3/16" v-notched trowel
    wet saw
    safety glasses

    PHOTO

    Figure A
    PHOTO

    Figure B
    PHOTO

    Figure C
    Glass Tile Backsplash

    • Dry-fit the tile sheets in the space to determine the best layout (figure A). A good layout minimizes the number of cuts and avoids tiny slivers of cut tile at the edges of the space.

    • Apply painter’s tape along the back edge of the countertop to protect the granite.

    • Use a 3/16" V-notched trowel to spread white tile mastic (adhesive) on the wall. The manufacturer recommended this mastic for this type of tile. It's important to use white adhesive, because any color behind the tile will show through the glass. To apply, hold the trowel at 45-degree angle and use the notched edge to make ridges in the mastic.

    • Before pressing the tile into the mastic, go back over the whole area with the flat edge of the trowel to knock down the ridges (figure B). This will prevent the ridges from showing through the glass. Even after they're knocked down, though, the ridges create air pockets that help adhere the tiles.

    • Set sheets of tiles into the mastic according to the layout (figure C). Apply firm, even pressure to each tile to make sure it's set in the adhesive. If tiles fall off the sheet, simply press them into the adhesive; the beveled tile edge provides the spacing needed.

    • Cut tiles as needed with a wet saw. If leaving the tile job to take a break or cut tiles, make sure to scrape off any excess mastic from the wall so that it doesn't harden.

    • Allow the adhesive to cure, then grout according to the manufacturer's instructions.


    RESOURCES :
    Tile
    Rubble Tile
    Website: www.rubbletile.com

  • ALSO IN THIS EPISODE:


  • Gutter Repair
  • Landscaping Basics
  • Flooring
  • UV Air Sanitizer
  • Replacement Windows
  • Planter, Self-Watering
  • Hand-Painted Glasses
  • Choose Washer/Dryer
  • Backsplash Installation
  • Hand-Painted Bowls
  • Prepare for Vacation
  • Maintain Garage Door
  • Disinfect Bathroom
  • Romance Kit
  • Curb Appeal
  • Transport Equipment
  • Installing Undermount
  • Holiday Decorating
  • Family Scrapbook
  • Ice Candle
  • Selecting Doors
  • Spark Plug, Changing
  • Maintain Cabinets
  • Front Door Facelift
  • Change Windowpane