How to Build a Grilling Island

Create an outdoor kitchen by nestling a gas grill into a custom-built, granite-topped island.

By: Dylan Eastman

An outdoor grilling island is a great way to create a custom cooking area without the expense of special-order appliances. Here we take a standard off-the-shelf grill and adapt it to island life.

DIY Network's Blog Cabin 2013 is a circa-1892 coastal cottage located along the Crystal Coast in North Carolina. The home has been remodeled, based on online voters' selections, and will be given away to one lucky winner in a home sweepstakes in Fall 2013. Pictured is the outdoor kitchen.

diy_bc13_outdoor-kitchen_06_grill-detail_h

DIY Network's Blog Cabin 2013 is a circa-1892 coastal cottage located along the Crystal Coast in North Carolina. The home has been remodeled, based on online voters' selections, and will be given away to one lucky winner in a home sweepstakes in Fall 2013. Pictured is the outdoor kitchen.

Photo by: Frank Murray

Frank Murray

Tools + Materials

  • tape measure
  • framing square
  • table and circular saws
  • 4' level
  • 15-gauge finish gun
  • bit driver and bits
  • pocket jig
  • 1 piece 5/8" pressure-treated or marine plywood
  • (10) 2x4 x 8’ pressure-treated lumber for the frame
  • (6) 1x4 x 8’ pressure-treated lumber for the frame
  • 1 1/2" 15-gauge finish nails
  • pocket and exterior wood screws (stainless or coated)
  • construction adhesive
  • countertop
  • exterior-grade 1x lumber for the cladding
  • grill
  • safety glasses
  • dust mask
  • work gloves
  • earplugs

Note: We used standard pressure-treated lumber to construct the fame and reclaimed pine for the cladding, but you could also use teak, mahogany or another exterior grade wood for the cladding. Masonry or metal are other options for the exterior cladding.

Take Measurements

Size up the base. Measure the width and depth of the grill, making sure to account for any items (i.e., gas lines) protruding off the back. Add 1/2 inch to each measurement. This will be the size of the opening created for the grill. Next, measure the distance from the ground to the lid and subtract 2 inches. This will be the countertop height. Then determine the total width and depth of the island. A good starting point is to multiply the grill width by three. This will give equal countertop area on both sides of the grill. Take the grill depth and add 6-1/2 inches to achieve the total depth.

BPF_original_tailors-tape-growth-chart_step-11_4x3

Construct the Island Frame

Frame the U-shaped top and base for the island using the total width, depth and grill opening dimensions. Frame each piece with pressure-treated 2x4 studs and wood screws.

BC13_Grilling-Island_DBLG705_2075

Construct Corners

Create the vertical corners by joining two pieces of 1x4 pressure-treated pine with pocket screws or face-driven wood screws. Subtract 3.75 inches plus the countertop thickness (usually 1 to 1.5 inches) from the overall countertop height to determine the lengths of the verticals.

BC13_Grilling-Island_DBLG705_2109

Assemble Parts

Add a 1x4 edge band around the top frame to support the countertop. Optionally, sheet the base frame with plywood if adding operable doors and storage in the island. Attach the base, verticals and top frame with four wood screws at each corner. Turn the completed frame over and install furniture-leveling feet at each corner and 2 feet on center across the back.

BC13_Grilling-Island_DBLG705_2123

Select Countertop Material

Consult a local countertop fabricator to select an easy-clean countertop material that will stand up to the elements. Once the material is selected and the lead time established, ask the installer to template the island frame, adding a 1 inch overhang around the perimeter. Be sure to account for the thickness of any cladding in addition to the overhang.

BC13_Grilling-Island_Granite

Install Frame

Install the island frame in its final position and check for level. Adjust the feet and, if necessary, add a plastic shim if the ground variance exceeds the range of the leveling feet.

BC13_Grilling-Island_DBLG705_2149

Cap Frame With Countertop

Install the countertop, being sure to have the grill handy in case any final adjustments are required to the top.

BC13_Grilling-Island_DBLG705_2153

Clad Exterior

The face of the island can be clad in a range of materials from metal to masonry or wood. In this case, reclaimed pine studs left over from a renovation were cut down into 3/4-inch strips and then installed with 15-gauge finish nails driven into the top and base framing. If installing a different material, such as masonry, it may be necessary to clad the exterior with sheathing first. Take this opportunity to decide if operable doors for storage in the base are necessary.

BC13_Grilling-Island_Cladding

Install Grill

Slide the grill into place, making sure not to crimp any exterior lines. Make sure grill front is flush with island face to allow for airflow behind the grill.

BC13_Grilling-Island_DBLG705_2205

Next Up

How to Build a Modern Outdoor Bench

Looking for more outdoor seating or a decorative bench for your porch? Try your hand at this easy woodworking project that can be built in less than a day.

How to Grow Cucumbers

Get advice for planting, growing and harvesting cucumbers, including suggestions for types and varieties to grow, companion plants, plus tips for solving common cucumber problems.

How to Build a Mandala-Style In-Ground Fire Pit

We made an in-ground fire pit, then decorate it with colored river rocks and sand to give it a mandala-inspired look.

How to Plan and Build an Outdoor Kitchen

Aesthetics are important but when it comes to building an outdoor kitchen, functionality and durability reign supreme. Read our professional tips to budget, plan and design an outdoor kitchen that will add value to your home and lifestyle.

How to Build a Floating Shelf With Hidden Charging Station

Don't let unsightly cables and cords clutter your living space. This DIY floating shelf has a built-in power strip tucked away in a drawer — the perfect spot to charge your phones, tablets and other gadgets out of sight.

How to Build a DIY Kitchen Island on Wheels

Need some extra workspace in your kitchen? Build a rolling island for added functionality and style. One side stores a stand mixer, sheet pans, cutting boards and more, while the other side allows for extra seating. Perfect for small spaces, this portable kitchen island easily rolls out when you need it and neatly tucks away when you don’t.

How to Build a Covered Sandbox

This weekend, build a covered sandbox for the kids. The roof on this DIY sandbox will keep the play area well-shaded and free of leaves, twigs and rain.

How to Replace a Window

When it's time to replace an outdated, inefficient window, it can be hard to know where to start, so we’ve got everything you need to know to get the job done.

How to Paint Laminate Countertops

New kitchen countertops can be an expensive upgrade. Transform your kitchen without breaking the bank by priming and painting your existing laminate counters.

How to Install a Kitchen Tile Backsplash

Learn how easy it is to install a kitchen tile backsplash with these step-by-step instructions.

Go Shopping

Get product recommendations from HGTV editors, plus can’t-miss sales and deals.

On TV

Follow Us Everywhere

Join the party! Don't miss HGTV in your favorite social media feeds.